GearTunes    > Treasure Chest    > Rockn Stompn    >

RS-4 Sequential Power Strip — List $379.00 Street: $299.

DISCRIPTION:

Model RS-4 is a foot activated sequential power strip with surge protection and EMI/RFI filtering, is designed to power up or down a individual musician's set of gear or equipment as a group in the proper sequence, every time. Model RS-4 is ETL listed in the United States and Canada conforms to UL Standard UL1449 Surge Protective Device and UL1363 for Relocatable Power Tap. Unit is 120V AC, 60HZ/15A includes four switched Duplex receptacles engineered to provide four step time delay activation and de-activation of the audio equipment plugged into it. Located on the front right side panel, there are two adjustable 16 position rotary switches, one for the on delay sequence and one is for the off delay sequence. Using any standard 1/8 inch straight blade screwdriver, or ROCKN STOMPN® screwdriver included in poly bag with instruction manual, you can select the desired delay from 0 seconds, meaning no delay at all, to 15 seconds delay between sequenced steps or receptacle, for a total delay of potentially 0 to 45 seconds.

 

A&E SPECIFICATION

The sequential AC power strip shall be ROCKN STOMPN LLC Model RS-4. It shall be ETL listed and have a power rating of 120VAC, 60HZ/15A with surge protection and EMI/FRI filtering and four switched duplex receptacles sequentially activated/deactivated equipment in four steps with user adjustable sequence delay from 0 to 15 seconds. It shall be housed in a welded 20 gage steel enclosure. Sequence activation shall be push button foot switch. Sequential AC power strip optional switch guard may be used.

 

Designed and manufactured in the Rockn Stompn U.S.A.

U.S.PATENT D663691 and PATENT PENDING

Power Rating 120VAC, 60Hz, 15A 1800W
Safety Agency Approvals ETL Listed file 4007270 in US and Canada conforms to ANSI/ UL Std. UL 1449-3 UL 1363 and certified to CAN/CSA 22.2 NO. 8
Actuation switch Push button foot switch (on- off)
Dimensions 13.25”L X 4.25”W X 1.50”H
Chassis construction Stainless Steel Welded 20gage
Receptacles (8) High impact thermoplastic (4) duplex receptacle Nema 5-15R
Power Rating 120VAC, 60Hz, 15A 1800W
Power Cord 15 foot 14 gage SJT Nema 5-15p
Surge Suppression (9) MOV’s 1935 Joules L-N L-G N-G Network UL1449-3
Circuit protection 15 AMP main power circuit breaker extreme over voltages over current shutdown with automatic resettable circuit
EMI/EMC Electromagnetic Interference (EMI) Filters-Fourth Edition; General Instruction No 1, 2 and 3;Issue:1982/09/01 (CSA C22.2 No. 8, with T.I.L No 516) 55022
Delay Sequence : 4-step 0-15 second adjustable delay sequence between receptacles for both on delay and off delay for potentially 0 to 45 second delay
Diagnostic Indicators: (4) LEDS one for each duplex receptacle indicating AC power to dedicated receptacle and power to controlling relay (1)LED front panel indicates electronic control module’s switching power supply and surge suppression network is functioning properly

Starting with the Ultimate Speaker Demo, an ever-increasing number of the GearTunes audio  clips are being tracked using the Radial JCR Reamp. The Reamp was invented by my good friend and colleague John Cuniberti who engineered/co-produced many of Joe Satriani's most infamous recordings.

For GearTunes, reamping allows me to record a track where the guitar "hears" the amp in the room, but initially only the guitar or guitar and effects signal is recorded. This allows me to spend additional time perfecting amp tones and mic placement once I have the performance I'm looking for. One of the byproducts of this process is the creation of GearTunes DI Clips which enable you to play select guitars and effects through your amp by using your mobile device or computer as a reamp device.

For GearTunes DI Clips - and Gear Tune DI Clips ONLY (always found under the DI clips tab for gear that has one), you can play our guitar and effects through your amp. Simply use an unbalanced cable that terminates with an 1/8th inch jack on one end and a 1/4 inch jack on the other. Connect the 1/8th jack to the output of your mobile device or computer and the 1/4 inch jack into the front of your amp. Start off with your amp volume at zero and your mobile device (or computer) volume all the way up to ensure you hit the front end of the amp with enough signal, and then gradually increase the volume of the clean channel on your amp until you reach a level that is not capable of causing damage to your ears or equipment. GearTunes accepts no liability for the use, abuse or misuse of these clips, and playing them into your amp is done exclusively at your own risk.

I am tremendously excited about being able to share GearTunes DI Clips with you as you journey on your quest to find right gear for the music you play! Cheers ~ Doug:)

Play Right Click to Download