The Afterneath will be available from dealers in September 2014. We will not be selling them direct until all dealer orders have been filled. No pre-orders will be accepted.
The Afterneath is an otherworldly reverberation machine that uses a swarm of short delays to create wild and cavernous reverbs and scattered, short rhythmic delays with bizarre characteristics. The reverb created is beyond massive and goes well beyond the territory of most reverb pedals. The controls allow you to stretch, smudge, swell and even self-oscillate into messy ambient washes of sound. The Length control adjusts the decay of the reverb; anything from shorter hall through endless plate style reverbs can be achieved. The Reflect knob controls the regeneration, basically feeding the output back through to create an even deeper otherworldly dreamscape. The Drag control lets you pull the reverb through time by slowing down or speeding up the reverb. The Diffuse knob adds control over spread of the reverb ranging from identifiable attack to a wash of smooth reverb. The Dampen control adjusts the tone of the reverb, both stinging bright tones and warmer swell. The end result is an ethereal, ambient wash that goes from hall to an infinite glitched-out orchestra pit warming up in a canyon at the bottom of another canyon inside a well. The Afterneath is true bypass with an all digital reverb engine, all analog dry signal path and hand made one at a time by real living human beans in dimly lit Akron, Ohio.
Length: Controls the decay length of the reverb.
Diffuse: Adjusts the spread of the reverb. Sharper with more attack counter clockwise, more ambient and washy as you turn it clockwise.
Dampen: Clockwise for brighter tones, counter clockwise for darker tones.
Drag: This digital reverb is made up of a bunch of short delays, this separates the delay lines creating a stuttering, pingy effect. This is the coolest control on the Afterneath, we highly advise slowly turning this while you let notes ring out for a cool warped speed effect. More delay as you turn it counter clockwise, more reverb as you turn it clockwise.
Reflect: Controls the regeneration of the reverb, turn clockwise for more wash and echos, counterclockwise for less. This will self oscillate if turned up high.
Mix: Blends the wet signal into the dry. Though it does not actually go full wet, it will gradually lower the clean level as you turn it clockwise and give the appearance of full wet.
4 5/8″ x 2 1/2″ x 2.25″ with knobs
A standard 9 volt DC power supply with a negative center 2.1mm barrel, no battery option. We do not recommend using this pedal on a daisy chain. Please use a a dedicated power supply or isolated output from a multiple tap power supply for best performance. Do not use any generic adapter (anything from RadioShack or similar). Do not run at higher voltages! Current Draw is 65ma.
Starting with the Ultimate Speaker Demo, an ever-increasing number of the GearTunes audio clips are being tracked using the Radial JCR Reamp. The Reamp was invented by my good friend and colleague John Cuniberti who engineered/co-produced many of Joe Satriani's most infamous recordings.
For GearTunes, reamping allows me to record a track where the guitar "hears" the amp in the room, but initially only the guitar or guitar and effects signal is recorded. This allows me to spend additional time perfecting amp tones and mic placement once I have the performance I'm looking for. One of the byproducts of this process is the creation of GearTunes DI Clips which enable you to play select guitars and effects through your amp by using your mobile device or computer as a reamp device.
For GearTunes DI Clips - and Gear Tune DI Clips ONLY (always found under the DI clips tab for gear that has one), you can play our guitar and effects through your amp. Simply use an unbalanced cable that terminates with an 1/8th inch jack on one end and a 1/4 inch jack on the other. Connect the 1/8th jack to the output of your mobile device or computer and the 1/4 inch jack into the front of your amp. Start off with your amp volume at zero and your mobile device (or computer) volume all the way up to ensure you hit the front end of the amp with enough signal, and then gradually increase the volume of the clean channel on your amp until you reach a level that is not capable of causing damage to your ears or equipment. GearTunes accepts no liability for the use, abuse or misuse of these clips, and playing them into your amp is done exclusively at your own risk.
I am tremendously excited about being able to share GearTunes DI Clips with you as you journey on your quest to find right gear for the music you play! Cheers ~ Doug:)
|Play||Right Click to Download|