Isolated power supply for pro stage and studio use
Pedal Power ISO-5 is an isolated power supply for powering guitar pedal effects and accessories. It's the ultimate compact solution for smaller pedalboards, rack shelves, or even as an additional power supply for larger boards. With five isolated, filtered and regulated output sections, ISO-5 keeps even the most sensitive vintage and boutique analog pedals dead quiet.
Pedal Power ISO-5 includes a high-current output which will properly power modern digital power-hungry effects like those from Eventide, Line 6, and TC Electronic. There's also a dedicated 18V output for those pedals which need the higher voltage for extra headroom.
Designed to meet the needs of professional users, Pedal Power ISO-5 will provide clean, consistent power, even with the poor AC line conditions often found on stage. Completely isolated output sections eliminate ground loops and unwanted interactions between effects, resulting in lower noise and noticeably improved tone.
Pedal Power® ISO-5 features:
Five isolated outputs
Compatible with all battery operated pedals
Includes high current 9V and 12V outputs, plus dedicated 18V output
Powers Boss Twin, Eventide, Line 6 modelers, TC Electronic Nova, Moog and more
Linear regulation and toroidal transformer for lowest possible noise
Compact design fits small pedalboards and rack shelves
Includes cables and detachable AC line cord
Engineered and handmade in the USA
Pedal Power ISO-5 is manufactured to operate from a specific supply voltage. There are three different models, which accept 100V, 120V, or 240V mains. All units sold in North America are for 120V only. You cannot operate a 120V model using 240V power without the correct step down transformer. The supply voltage is marked on the bottom of the unit.
Short Circuit Protection
Every output on Pedal Power ISO-5 is individually short-circuit protected. This means that if you have a short in a power cable, or one of your pedals malfunctions, ISO-5 will turn off the power to only that pedal. All other outputs will continue to function normally with no long-term damage.
Pedal Power ISO-5 Specifications
Detachable IEC (computer-type) line cord
120V 50/60Hz (North America model)
100V 60Hz (Japan model)
230V 50/60Hz (Europe/Australia model)
Model and input power are marked on the bottom of unit.
5.5x2.1mm barrel connectors center negative
Short circuit protected
9VDC (3) - 100mA
9/12VDC - 300mA
18VDC - 100mA
5.5x2.1mm right angle barrel connectors (4)
5.5x2.1mm right angle to straight barrel connector (1)
5.5x2.5mm right angle red barrel (1)
3.5mm right angle mini plug (1)
4.9" wide x 3.4" deep x 1.8" tall (124 x 86 x 44 mm)
Weight: 1.24 lbs (0.56 kg)
Toroidal power transformer
Starting with the Ultimate Speaker Demo, an ever-increasing number of the GearTunes audio clips are being tracked using the Radial JCR Reamp. The Reamp was invented by my good friend and colleague John Cuniberti who engineered/co-produced many of Joe Satriani's most infamous recordings.
For GearTunes, reamping allows me to record a track where the guitar "hears" the amp in the room, but initially only the guitar or guitar and effects signal is recorded. This allows me to spend additional time perfecting amp tones and mic placement once I have the performance I'm looking for. One of the byproducts of this process is the creation of GearTunes DI Clips which enable you to play select guitars and effects through your amp by using your mobile device or computer as a reamp device.
For GearTunes DI Clips - and Gear Tune DI Clips ONLY (always found under the DI clips tab for gear that has one), you can play our guitar and effects through your amp. Simply use an unbalanced cable that terminates with an 1/8th inch jack on one end and a 1/4 inch jack on the other. Connect the 1/8th jack to the output of your mobile device or computer and the 1/4 inch jack into the front of your amp. Start off with your amp volume at zero and your mobile device (or computer) volume all the way up to ensure you hit the front end of the amp with enough signal, and then gradually increase the volume of the clean channel on your amp until you reach a level that is not capable of causing damage to your ears or equipment. GearTunes accepts no liability for the use, abuse or misuse of these clips, and playing them into your amp is done exclusively at your own risk.
I am tremendously excited about being able to share GearTunes DI Clips with you as you journey on your quest to find right gear for the music you play! Cheers ~ Doug:)
|Play||Right Click to Download|